WW2Treasures

Announcement

Collapse
No announcement yet.

NSDAP Gold badge.Opinions please

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    NSDAP Gold badge.Opinions please

    Friends I have a question. There is a small shift on the badge .On the many badges the letter "A" is exact on the center of the wreath.The opinions is necessary. All thanks.

    #2
    At times the letter A can be off center. From your Pic the badge looks original to me. Post the reverse to be sure though.

    Comment


      #3
      Andre,
      I believe the centre may have come off and been replaced slightly off centre due to the heat used in the repair to the back.

      Robin Lumsden has a Golden Party badge with the centre slightly off and he says that some were manufactured this way.

      The badge is certainly an original.

      Cheers,
      Brett
      Attached Files

      Comment


        #4
        Reverse showing the repair...
        Attached Files

        Comment


          #5
          Looks like a very early number too

          Comment


            #6
            Originally posted by ErichS View Post
            Looks like a very early number too
            Friends!!! As similar repair can lower cost of the badge? And how many it can cost today? Thanks.

            Comment


              #7
              It's an original badge and with a very low number. That low number will not make it cheaper but either more expensive!

              Regards, Theo
              Freedom is not for Free

              Comment


                #8
                Friends about what speaks early number? And what can be real cost?
                Last edited by Andre Murti; 02-09-2007, 02:13 PM.

                Comment


                  #9
                  Friends there is a question!!!! "4" in this badge differs from a usual writing. Why so?

                  Comment


                    #10
                    Because your badge has what is called "rotograving" and not the normal stamped numbers.

                    My personal feeling is that these are replacement badges made without a number. When someone loses their badge and requests a replacement then the factory engraves the number on as they can't stamp a number on a completed badge.

                    Could also be due to the fact that it was a quicker method to engrave them, but either way they are a later badge more so than early.

                    The badge is worth what the seller is asking for it as he has priced it fairly.

                    Comment


                      #11
                      Brett has a point there. The type of digits they have used by this one is completly different to the original that were pressed into the badge. Those digits have a very characteristic apperiance.

                      Regards, Theo
                      Freedom is not for Free

                      Comment


                        #12
                        Originally posted by Theo Cuypers View Post
                        Brett has a point there. The type of digits they have used by this one is completly different to the original that were pressed into the badge. Those digits have a very characteristic apperiance.

                        Regards, Theo
                        Theo OK, And what is conclusion from this ?

                        Comment


                          #13
                          Bottom line is both types of numbering are correct, and that pin is a good one.

                          Comment


                            #14
                            Originally posted by Jon Fish View Post
                            Bottom line is both types of numbering are correct, and that pin is a good one.
                            Friends who can show or tell where is it possible to see,
                            both types of numbering ??????
                            As I see similar numbering for the first time.

                            Comment


                              #15
                              It is interesting to note that on ALL roto engraved badges you see lines from the pin plate to the bottom of the badge like the badge pictured. Could these be grinding marks removing the old number and a new number applied? Could these be re issued badges? Any opinions?

                              Comment

                              Users Viewing this Thread

                              Collapse

                              There is currently 1 user online. 0 members and 1 guests.

                              Most users ever online was 10,032 at 08:13 PM on 09-28-2024.

                              Working...
                              X