Warning: session_start(): open(/var/cpanel/php/sessions/ea-php74/sess_7bacc2a4aa7df68a399b905f26c4004130e0a06c5211cdc6, O_RDWR) failed: No space left on device (28) in /home/devwehrmacht/public_html/forums/includes/vb5/frontend/controller/page.php on line 71 Warning: session_start(): Failed to read session data: files (path: /var/cpanel/php/sessions/ea-php74) in /home/devwehrmacht/public_html/forums/includes/vb5/frontend/controller/page.php on line 71 Panzerschreck rocket connector - Wehrmacht-Awards.com Militaria Forums
Emedals - Medalbook

Announcement

Collapse
No announcement yet.

Panzerschreck rocket connector

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Panzerschreck rocket connector

    Hi all,
    I am looking for some pictures of the wood block connector that was taped to the fins of the Panzerschreck rocket. With all the rockets found, many with the igniter still in the rocket venturi, I am amazed that no one has found this part in any condition. At the very least, I would think that the metal pin at the end of the wire would have survived after the wood rotted away on at least ONE example. I would like to see how the wire was attached to the pin. Pictures from the manual seem to indicate that the wire passed through the pin, what kept it in place ? Also was the pin split like a lot of German radio connector pins ?
    I recently saw some pictures on the web of the excellent weapon collection at the National Museum of Military History, Diekirch, Luxemburg and in collection room no.8 there were Panzerschreck rockets that appeared to have the wood blocks on the fins. One was on the wall with the launcher and two were in a crate. None look attached with the strip of tape and the blocks on the rockets in the crate could have been there to wedge the rockets in place. The one on the wall was attached by other means and didn't need a wood block unless it was original.
    If anyone has an example of the connector or is going to Luxemburg and could take some pictures, it would be greatly appreciated.
    Best regards,
    Bill

    #2
    Here's what I'm talking about, a picture that shows a firing pit with a team loading a schreck with another rocket. I say another because nearby, lower right, is the wood block connector with the transport tape on it from a previous rocket waiting for someone 67 yrs in the future to find it.

    http://www.ullsteinbild.de./photodat...w/00281715.jpg

    How many of you folks have come across firing pits ? Those connectors are out there waiting to be found. Well, one can only hope !
    Thanks, Bill
    Last edited by bogdan; 07-02-2011, 01:25 PM. Reason: lousy grammer

    Comment


      #3
      I dont know if these pictures help you.

      These are from Finnish army PanzerSchreck documents.I can make sharper scans if you need,i have original printed cardboard teaching prints of army.



      Comment


        #4
        Hi jiipee,
        Thank you VERY much for those scans. They help a great deal in my understanding the setup of this connector. Is there anything on the poster that says how the wire is attached to the pin, solder or press fit ? By the looks of the pin it has a single slot cut down it's length. Again thank you very VERY much for this info.
        Regards,
        Bill

        Comment


          #5
          Hi jiipee,
          I was looking at the scans and was wondering if the round feature on the side of the forward part of the rocket fin assembly is the same as on the cutaway drawing. It appears to be the spot where the grounding wire for the igniter is soldered. I ask only because the spot is in a slightly different position on the full surface drawing than on the cutaway in relation to the forward edge of the base of the fin assembly.
          Thanks,
          Bill

          Comment


            #6
            Originally posted by bogdan View Post
            Hi jiipee,
            I was looking at the scans and was wondering if the round feature on the side of the forward part of the rocket fin assembly is the same as on the cutaway drawing. It appears to be the spot where the grounding wire for the igniter is soldered. I ask only because the spot is in a slightly different position on the full surface drawing than on the cutaway in relation to the forward edge of the base of the fin assembly.
            Thanks,
            Bill
            It shows same grounding spot from littlebit different angle.

            Comment


              #7
              I did a mockup of the igniter to woodblock connector in photoshop which can be seen here:

              http://warrelics.eu/forum/ordinance-...onnector-8074/

              or here:

              http://www.bocn.co.uk/vbforum/thread...onnector/page2

              Sorry, can't post attachments.
              Regards,
              Bill

              Comment

              Users Viewing this Thread

              Collapse

              There is currently 1 user online. 0 members and 1 guests.

              Most users ever online was 10,032 at 08:13 PM on 09-28-2024.

              Working...
              X